GX Front Bumper | Strike | 460 (10+)
★★★★★ ★★★★★ 5.00/5 Stars. (4 Reviews)
Weight: 130 Steel | 70 Aluminum (lbs)
Looking for answers to common questions about us or our products? See our FAQ here.
11 Questions asked on GX Front Bumper | Strike | 460 (10+) •
Ask us anything
Q Brac • 05/18/2021, 10:31:52 PM The weight for the steel option is listed at 160lbs. Is that correct? It looks like the strike bumpers for other vehicles are around 90-110lbs. What makes this one so much heavier? Can you list out the weight difference between no bars and the full bars?
A 05/21/2021, 10:34:23 AM That weight was for the full grille protection option sorry. The base bumper weighs 130 lbs in steel.
Q Reed • 06/04/2021, 1:19:40 PM Where can I find the install directions? Wondering how much cutting is needed, Thanks
A 06/11/2021, 3:00:33 PM Still working on the install video and doc, will be updated on this page when available.
Q Lito Mercado • 07/10/2021, 0:35:12 AM If I ordered this bumper but in aluminum , would you be able to send it to a residential address GX FRONT BUMPER | STRIKE | 460 (10+)
A 07/23/2021, 10:58:16 AM No, the size is the issue, not the weight.
Q Jay Doshi • 09/05/2021, 12:30:18 PM Where were the fog light wires connected to? the cube amber lights? I don't think that was mentioned in the video. Where can I find turn signal lights that fit the provisions on this bumper?
A 09/07/2021, 1:14:21 PM Yes, the fog light harnesses were tied into the cube lights. The turn signal lights are included.
Q Michael Block • 10/13/2021, 11:15:50 PM What is the alloy of the steel or is basic mild steel?
A 10/28/2021, 11:38:26 AM It's A36.
Q Jeff • 10/23/2021, 0:04:41 AM I have a 2021 Lexus GX460. In your video for your strike bumper do the new "cube" fog-lights wire DIRECTLY to the OEM fog-light wiring? If so, which cube-lights do you recommend? And will there be any electrical issues wiring directly to the OEM wires?
A 10/28/2021, 11:56:03 AM We recommend Baja Designs lights. No, no issues. In many cases LED cube lights draw much less power than stock incandescent lamps.
Q David Lindstrom • 12/12/2021, 6:46:59 PM I know there’s a note that a particular light bar isn’t compatible, is there a model that you recommend?
A 12/13/2021, 9:30:55 AM We recommend the Baja Designs S8 20" bar! You can search for it on our site.
Q AJ • 01/17/2022, 12:46:18 PM For the aluminum bumper, is the winch mount steel or aluminum as well?
A 01/18/2022, 10:53:15 AM It is aluminum as well. The fully welded winch plate is gusseted and tied into all structural components of the bumper assembly to create a rigid weldment that spans and reinforces both frame mounting points to eliminate bending and twisting.
Q Paul • 05/31/2022, 2:19:34 AM On 14+, is the wiper fluid resv, relocated? I didn’t see it pictured in your images.
A 06/09/2022, 3:18:46 PM It has not been relocated, no.
Q Ben Davis • 07/27/2022, 2:21:26 PM Does it interfere with the front camera?
A 08/15/2022, 4:41:47 PM With a front camera, we would run the no tube work version.
Q Youcef A • 10/19/2022, 2:38:57 AM Will the Badlands Apex 12k winch fit in this bumper?
A 10/20/2022, 10:16:58 AM Yes, but you may have to relocate the solenoid pack.
5.00/5 Stars out of 4 Reviews
Write a Product Review: GX Front Bumper | Strike | 460 (10+)
Santis Limezs (NC) | January 18th, 2023
Installed aluminum version on 2013 GX460. Quality, fit and looks are good! Instructions are absent so all you have is video. The cut measurements were just the starter and only in the wheel corners was it the right amount. The rest of it had to be trimmed several times while fitting. For 2013 you have to splice into main turn signal wire at the top of lights. The fog light shelf was too low and also the hole seems to be lined up too close to the middle for BD SAE lights. Also wish there was no logo in bar light slot and slots for holding screws should be made at angled or indented from side so that over time BD S8 light would not fall out. Was able to install Warn Zeon S10 with long relocation kit snug against the power steering line without moving it. Brackets which go over frame are not marked L/R so just make sure the extra hole points outward. That bolt which is provided for the 5/8" hole in bracket is too big so just get a different 1/2" bolt same lenght from a hardware store which will fit in 5/8" drilled hole.
Scott D. Sturgis (MI) | May 31st, 2022
I installed the aluminum Strike bumper over a weekend. The bumper is very well built and fit perfectly, however the only installation instructions you get is a video. I found the video pretty good, but a lot of details are missing. After the installation I found that I had not used about 30% of the hardware that was shipped with the bumper. Tried to call for information, but their call center is only open M-F. Kind of pointless since most do-it-yourselfers do projects over the weekend.
Anthony Russell (DeSoto, Tx) | May 1st, 2022
Very nice bumper . The finish was amazing. Install video is very informative. You do need to relocate you power steering cooling line if you use a winch. It’s also much easier with the bumper out of the way. Rent a good transmission jack to aid in your installation. Very good quality. Did I mention the finish? It is almost perfect.
Nomad Outfitters (Colorado) | January 31st, 2022
Great looking bumper, but the cut line directions are off a good inch. Besides that it's one of the best looking aluminum GX460 front bumpers on the market. Our client is very pleased with the overall fit and finish and we will be buying again. Thank you, Tyler
Please note: Install videos are meant to be used as a guide, and aren't always the most up to date information on product installation and improvements.
Please be sure to read the PDF installation instructions (if available) as well.