• Victory 4x4
    0

    Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)

    4.3 · 3 ratings
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    • Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)
    Fit at a Glance More questions? See the FAQ
    Fits
    2003+ Chevy Express and GM Savana, regular and extended body
    Load
    300 lbs dynamic, 800 lbs static
    Install Time*
    Home: 1 day · Shop: 3 to 4 hr
    *Times are estimates and vary with vehicle condition and installer skill.
    $2,099.20
    Regular
    $2,624.00
    Black Friday All Month Sale – Save $524.80
    $14.95 Flat Rate Shipping

    Code: VGMVRK | Weight: 90 (lbs)



      Chevy & GM Van Roof Rack | Chevy Express & GM Savana (03+)

      Specs
      Vehicle2003+ Chevy Express & GM Savana
      Material3/16" aluminum with steel mounting brackets and extruded aluminum rails
      FinishSatin textured black powder coat over zinc primer
      Crossbars12 (regular body) / 14 (extended body)
      Load Rating300 lbs Dynamic / 800 lbs Static
      WarrantyLimited Lifetime

      Need to haul gear that doesn't fit inside your van, or ready to add more cargo capacity? This roof rack gives you a solid, secure place to mount almost anything up top, so your gear has a place to go and your interior stays free for the essentials.

      This rack is built from extruded aluminum rails with steel mounting brackets, giving you the strength you need without adding unnecessary weight. Milled T-nut access points run the length of the rack, so you can mount gear anywhere along the top, and easy bolt-together installation means no drilling into your van's roof.

      Features
      • Laser cut and formed from 3/16" aluminum with steel mounting brackets and extruded aluminum rails for lasting strength
      • Milled T-nut access points let you mount gear anywhere along the rack
      • 12 crossbars on regular body vans, 14 on extended body vans, for flexible gear mounting
      • Easy bolt-together installation, no drilling required
      • Fairing edge trim included
      • Available with or without a 40" light bar cutout (light bar not included)
      • Hardware included
      • Paint protection film, anti-seize and Ultra Black sealant included
      • Made in the USA

      Extra Mounting Hardware
      Need extra hardware for more accessories? Grab the T-Slot Nut and Stud Kit (set of 12), or the T-Slot Nut and Bolt Kit and T-Slot Stud Kit.

      Fitment & Notes
      • Fits 2003+ Chevy Express & GM Savana
      • Rated for 300 lbs dynamic load (while driving) and 800 lbs static load (when parked), evenly distributed across the rack
      • Light bar cutout version includes light bar mounting brackets. Cutout fairing fits a 41.25" max lens housing width single-row LED light bar; bars up to 43.5" (mounting stud width) will fit with our mounts, but trimming the fairing is required
      • We recommend applying paint protection film (included) under the front and rear fairings where they contact the vehicle, to prevent dirt and debris from scratching paint over time
      • Backed by a limited lifetime warranty against material, manufacturing, and design defects. See our warranty page for full details

      A quick note on weight ratings:
      These are a guide, not a replacement for your vehicle's manufacturer roof load limits or GVWR, so check your owner's manual first. Added weight changes handling, especially off-road or in an emergency maneuver, so load smart. As with any modification, you're responsible for how it's installed, loaded, and used.


      Made in USA

    What comes with the roof rack besides the hardware?
    Every rack includes paint protection film for the contact points, anti-seize for the bolts and Ultra Black sealant for the roof mounts, so you have everything you need for a clean, protected install.

    Which vans does it fit?
    It fits the 2003+ Chevy Express and GM Savana, regular and extended body.

    How many crossbars does it have?
    12 crossbars on the regular body and 14 on the extended body.

    How much weight can it hold?
    It is rated for 300 lbs dynamic (while driving) and 800 lbs static (when parked), evenly distributed.

    Can I run a light bar?
    Yes. Choose the light bar cutout version, which includes mounting brackets. The fairing fits a single-row bar up to 41.25" lens housing width, and bars up to 43.5" mounting stud width fit with trimming of the fairing.

    Will the fairings scratch my paint?
    We recommend paint protection film (included) under the front and rear fairings where they touch the vehicle.

    Still have a question about fit?Talk with the team that builds it, right here in Kalamazoo. Mon to Fri, 8:30 AM to 4:30 PM ET.

    Customer Reviews

    4.3
    3 ratings · 3 written
    5★1
    4★2
    3★0
    2★0
    1★0
    Oct 13, 2025

    1999 Chevy Express 1500 (Short wheelbase)

    Spoiler alert:
    My overall rating for the rack itself is 5 stars. However, my overall rating for this purchase, is 4 stars, which is reflected in this review. I would highly recommend this rack, and if I had to do it again, I would. In my opinion, the rack you are getting is far better than all the other racks out there, for a fraction of the price. That said, if you are planning on buying one of these, I highly suggest you read the more detailed review that follows:

    As the title suggests, I purchased this rack for my 1999 Express, knowing that Victory sold it as an '03+ rack. For those that are wondering, the transition from '02 to '03 for the Express/Savana was basically just a facelift at the front of the van, and pretty much everything else stayed the same. That means many factory parts are interchangeable between the two generations even if the part specifies only one generation. For example, I upgraded my 1999 undersized sideview mirriors with the larger '03+ version that had both the integrated blindspot mirror as well as the turn signal! The wiring for the turn signal was ALMOST plug and play, but did require some modification to the harness to get it to work properly.

    Anyway, back to the rack!!!! I just installed this rack the same weekend I am providing this review. After I've had time to actually use it, I'll return and provide additional feedback if the website allows me to edit.

    Shipping/Receiving:
    I'm giving Shipping/Receiving 3 stars and here's why. Sadly I was missing a couple key parts (two of the four midpoint "upper" mounting brackets), one of my 12 extruded aluminum cross rails looked like someone took a machete to it prior to packing it and it had deep gauges and scrapes in it, and lastly, the front facia has multiple scratches on it's face. Being that it's still the weekend, I have not had a chance to reach out to Victory for a resolution to these issues. I'm confident they will handle it appropriately.

    For the record, all these aforementioned items were packaged properly and this damage was only discovered after removing the significant amount of padding it had been shipped in. This tells me these items were damaged prior to shipping, which tells me there is a quality control issue during shipment preparation at Victory. There is no way this damage should not have been seen prior to wrapping it and sticking it in the box. As for the missing parts, I can somewhat forgive that because there are a lot of parts in this kit, and I get that things can and do get overlooked at times, but that still reflects poorly on Victory for not being more thorough, hence the 3 star for shipping.

    Assembly:
    Overall I give assembly 4.5 stars. While I know everything these days is digital, it still would've been nice to have a printed copy of the instructions provided with the rack, rather than telling the customer to look at the PDF on the website. If providing customers a printed copy is really that much of a hardship, then just raise the price $5, throw in a hardcopy, and call it a day. As another reviewer pointed out, there was TONS of extra hardware included that had nothing to do with this product. While not a problem, it would've been nice if the instructions educated you on the fact that they provide a universal hardware pack, so you don't go so long wondering what you're doing wrong having so many leftover parts before realizing on your own what's really going on :) Overall though, assembly went quickly and was very easy. You definitely want to make sure you're working on a flat padded surface of some sort to keep from scratching up all your parts, or the leading and trailing corners of the side rails once it's fully assembled.

    Installation/Alignment:
    This gets 5 stars. The instructions suggested assembling the two halves on the ground and then placing them on the roof before attaching them together into one large piece. I get why they suggest this, because once assembled the rack does have a good bit of weight to it, albeit still very light for its overall size. That said, I was concerned about getting things moved around on the roof and lined up for assembly without scratching my van, and all while working from a stationary ladder. If you have the benefit of platforms you can place along each side that make it easy to move along the length of the vehicle without constantly moving a ladder, then this may not be an issue for you.

    So instead, I assembled the entire rack on the ground before placing it on the van. For those that may want to try this approach I'll briefly describe how I got it on the van after assembly without damaging my van. First I had my 65 pound, 12yr old daughter get on the roof, and my wife and I each grabbed one end of the rack and lifted it above our heads. I had placed a slippery blanket on the roof toward the rear of the vehicle, and then placed several foam blocks on that. Working from the rear of the vehicle, I placed the front end (front facia) of the rack on the stack of blocks. Then I joined my wife at the tail end of the rack, and as we pushed the rack forward from our location on the ground, my daughter from her perch on the roof pulled and guided the rack straight, and we slowly slid it onto the roof. At no point was the rack ever in contact with the van's roof, and it wasn't until we had it in position (I'll get to alignment in a moment) that we removed the blanket/blocks from under it to lower it into its new home. If you don't have a small child to place on the roof, and you're strong enough to work the rear end of the rack by yourself, then your helper could get alongside the van on a ladder or stand in the open side doors, and manipulate the rack from there. You could also use a third adult for this function if you need two people at the rear pushing.

    As for alignment, the instructions never really give you good guidance on this. They mention don't going further than your front mounted roof antenna, but that seems like a no brainer. Problem is I have an '99 van and no roof mounted shark fin antenna. So I looked on the website at the product images they provide. While it isn't immediately obvious, they actually show this rack on both a long and short wheelbase version of the van. I have a short wheelbase, and luckily one of their pictures is of a short wheelbase van view directly from the passenger side. Also seen in the photo is a bike rack attached to the rear of the van. The reference point I noticed made the most sense to me was the rearward of the two midpoint mounting locations. It was perfectly centered directly above the rear edge of the door opening for the double side doors. This location worked perfect for me on my '99 short wheelbase variant.

    Mounting:
    Sadly mounting gets 3.5 stars, mostly because it wasn't until I had the rack on the roof and started to bolt it down before I discovered I was missing two key components for two of the four midpoint mounting positions. I also give mounting a lower score because Victory suggests you should just "pound" the brackets into position if they don't line up quite right on their own. I was not about to beat this thing into submission to get brackets to line up correctly, knowing that doing that would easily have damaged painted surfaces on the van and would lead to rust and failure later on. I wish Victory had put a little more effort into their brainstorming on how to coach these components into place, before making what I believe to be a very poor suggestion to their customers.

    That said, it only took me working on the problem myself about 10 minutes to come up with a far simpler, safer, and effective method. I will describe it here, but keep in mind this will make no sense to you until you own one of these and are at this point in the process yourself. The rail mounting hardware consists of two primary components, what I'll call an "upper" and "lower" bracket for each mounting location (8 locations in total). The lower bracket is hard mounted to the rack's side rail during assembly and as such are rigid in nature, and will not move once assembled. They ultimately are the component that rests in the vehicle's rain channel itself. The upper bracket is the last part you will add to your rack once it's in position. They attach to the rack's side rail and extend outboard beyond the vehicle's gutter rail. When installed they should fully "wrap around" the entire rain gutter and then bolting them into the rack is the action that draws them back inboard effectively clamping the vehicle's rail between the rack's lower and upper brackets. The issue is, once you've attached the upper bracket to the rail, and you attempt to position them "over", "beyond", and "around" the rail, they will more than likely NOT actually reach far enough outboard, and because of alignment tolerances likely not wrap around the rail itself. This also prevents you from being able to anchor them to the rack as well as the lower bracket.

    This is where Victory suggests getting a mallet to it and beating on them until they pop down into position. I wholeheartedly disagree with this suggestion. This will easily scratch and even chip paint off your vehicles rail, leading to rust and future failure. The solution I came up with is far less aggressive and has zero potential of damaging the paint on your vehicle, or its physical structure. I'll spare you how I came to this solution and simply explain the process itself. At a mounting location, you should slightly loosen the two 1/4-20 button head bolts that are attaching the lower bracket rigidly to the side rails of the rack. Once you've done this you should have no trouble placing the upper bracket over/around the rain gutter rail of the vehicle and then installing (loosely) the three hex head bolts used to attach it to the rack's side rail (two bolts), and the lower bracket (one bolt). Once you've gotten those three bolts loosely in place, you then retighten the 1/4-20 button head bolts that secure the lower bracket to the rack's side rail. This action quickly draws the lower bracket fully and rigidly back in its place but also leaves the upper bracket properly portion over and around the vehicle's rail. Once you've done this you should begin to slowly tighten the two hex head bolts holding the upper bracket to the rack's side rail, until the upper and lower brackets are firmly clamping the vehicle's rain gutter. At this point, tighten the 3rd and final hex head bolt that locks the upper bracket into the lower bracket.

    Sorry for how wordy that all was, but trust me the process worked without issue at all six of the eight mounting locations I was able to do. The remaining two locations I wasn't able to do because two of the upper brackets needed for two of the four mid-point mounting locations were missing from my shipment. As I mentioned previously, everything I just described will make far more sense once you're actually looking at this thing on your roof and having to secure it.

    I really hope Victory can accommodate such a long review, and I also hope they will take a look at improving their quality control processes a bit too. Overall though I have no major complaints. I communicated with them over the phone several times leading up to this purchase asking questions, and they were very prompt and helpful every time. Once again, I would buy this rack again if I had to do it over again, and I would highly recommend it to anyone else.

    Ralph
    Oct 6, 2023

    Happy Happy Roof Rack

    First off I would like to say thank you Victory for making a roof rack that fits a Chevy/GMC van. I have had mine for over two years and enjoyed it very much. Mine may have been the second one manufactured ....For a market that really does not cater much to the Chevy/GMC van overland community its been a joy to have a stylish looking roof rack. Looks much better than the few competitors racks that are available. It is very versatile and the accessories that I have purchased from Victory have been awesome additions to the system. When I have had any questions I have received a quick response with solutions that have been helpful. If your are in the market do not hesitate its well worth the investment if your going to use it like it should. Thank you again Victory for a spectacular product that looks Kick Ass!!!

    Dustin
    Response from our team

    Thanks Dustin!

    Feb 21, 2022

    Slick roof storage solution for Express

    I have a 2018 Express extended body so finding racks for this is challenging. There is at least one on the market that is welded but the original cost plus shipping was steep. This one arrives flat packed in a few boxes. Everything assembled properly per the instructions. For some reason I ended up with a ton of extra hardware (60 or 80 additional bolts, washers, nuts, etc.) some of which were not for this rack. They have been useful though for other projects. The rack is assembled in two pieces and then lifted onto the roof. This was mildly challenging with two adults and two ladders. Having the ability to move a little more side to side while you install would be useful so perhaps setup some rudimentary scaffolding or some type of platform rather than just using a ladder. The brackets that attach the rack to the rain gutter were a little tricky but some patience and a rubber mallet (recommended by instructions) we were eventually able to get each of these to seat properly. The sealant in the gutters is not even so you have to wrestle with everything to get it attached solidly. The brackets will seat into the gutter with the right amount of effort. The only real issue I have run into is the front fairing. The instructions state that you need to push it down agains the roof as much as possible to avoid vibration. It is currently set as low as possible given the cutouts in the side pieces where the fairing mounts. It is also touching the roof in some spots, although the shape does not allow for a tight fit. The fairing vibrates horribly at 60+ mph. It sounds like a lawn mower or something on the roof. The fairings are made from the same material as the sides which is easily flexible until the cross beams are installed. However, the fairings only get bolted on the ends so this large flat pieces of metal easily bows and flexes by hand or with the wind. The only solution I can come up with is to try and bolt a piece of angle across the back to reduce the flex. This should be included with the rack because the fairing vibration is a weak point in an otherwise nice roof rack setup.

    Christopher Stone
    Response from our team

    Christopher, please reach out to our tech support team and we can help with that front fairing adjustment.

    Reviews come from our customers. Buyers are invited to rate their parts after their order ships, and those reviews are marked Verified Buyer. We publish positive and negative reviews alike.

    Real builds from Victory4x4 customers.

    Customer photo
    Customer photo


    ACCESSORY MOUNTS

    A wide variety of accessory / lighting mounts available and the list is growing!

    See related products below!



    SUNROOF COMPATIBLE

    Allows for full functionality of all standard sunroofs



    BUILT FOR ADVENTURE

    Designed with your outdoor gear in mind.





    Related Products